Rune Central

The Official Rune Quake Message Board
It is currently Thu Mar 28, 2024 7:42 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 2 posts ] 
Author Message
 Post subject: Can't Connect To Server!
PostPosted: Wed Apr 23, 2008 5:01 am 
Offline

Joined: Sun Mar 09, 2003 10:47 pm
Posts: 1612
Location: Ohio
There are types of "Can't Connect" To Server Issues. Both are easy to fix.

1) The "Connection Accepted" problem - You can connect, but it just sits there and does nothing.

This is because the original Quake is not NAT fixed and if you have a router or a dsl/cable modem with router capabilities, Quake does not know how to successfully do the connection handshake.

You can easily fix this by using one of the many NAT-fixed clients:

1) (HomePage) Modern ProQuake 3.99
2) (HomePage) Qrack
3) (Homepage) Historical ProQuake 3.50 (Warning: Does not have fix #2, see below!)
4) (HomePage) JoeQuake (Warning: Does not have fix #2, see below!)
5) (HomePage) DarkPlaces

2) The "Quake won't connect at all, but my internet works" problem

This usually happens with DSL. If you have multiple IP addresses due to having DSL or a router or a 2 network cards, Quake uses the first one. With DSL, this is always an invalid IP address and many other setups may have this issue.

The following clients have the ability to properly connect under almost any network setup or combination of DSL/LAN/Router/Etc and will never have this problem.

You can, technically, fix this problem with Historical ProQuake 3.50 or JoeQuake by adding -ip x.x.x.x to your command line, but with DSL your IP address changes every time you establish a connection, so no one does this and it is a major hassle. None of the following clients need you to do that, they do it automatically.

List of clients with this fix:

1) (HomePage) Modern ProQuake 3.99
2) (HomePage) Qrack
5) (HomePage) DarkPlaces

3) Some other problem

If you are using either Modern ProQuake 3.99, Qrack 1.85 (or later) or DarkPlaces and have a connection problem, check your firewall (Norton or whatever you are using), this is almost certainly the problem. If you have seriously messed with your router settings, you might check that as well but that is very rare. Make sure you are typing the server address correctly too.


Top
 Profile  
Reply with quote  
 Post subject: Re: Can't Connect To Server!
PostPosted: Sun Jul 13, 2014 8:22 am 
Offline
User avatar

Joined: Tue Jul 08, 2014 1:46 pm
Posts: 29
Location: Toronto Ontario
HI there, just a suggestion that may apply to some proquakers. I run proquake 4.93, and I was having "connection accepted" error, as mentioned above, and the console was showing two IPs. I have a simple fix not mentioned above. You can add -oldnet to the target in the properties of the exe. Here's what you do.

Create a shortcut to glpro493.exe, or dxpro493, depending on which you use.

Right click on the shortcut, and open properties.

Go to the shortcut tab at the top of the shortcut properties window.

There should be a box named target, and the text beside it should read something like "C:/Programfiles/proquake_493/glpro493.exe"

At the end of that, and a space and then -oldnet.

The new target should be "C:/Programfiles/proquake_493/glpro493.exe" -oldnet

Hit apply and use that shortcut to launch proquake, and you should be set.

Please not that this works with proquake version 4.93, and the folders, folder locations, and exe names may vary depending on where you installed proquake, and what you named the files.

Happy quaking.

_________________
Sincerely SPF


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 2 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 6 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group